If the part is soldered once and never touched again, use an open pin header. If a cable gets plugged in during assembly or in the field, use a box header. The shroud and the keying slot cost a little more, and they stop the two failures that actually happen: a connector pushed on one pin off, and a cable inserted backwards.
Both parts sit on 2.54 mm pitch, both carry 3 A per pin, and both come off the same stamping die in our shop. The decision is about handling, not electrical performance.
What changes when you add the shroud
A box header is a pin header with a plastic wall around the pins and a slot on one side. The wall guides the mating connector in. The slot only lets it go in one way.
On an open header the pins are exposed. Nothing guides the mating part. If the assembler is working at an angle, or the cable is short and pulls sideways, the socket can land between pins. Sometimes it goes on and works. Sometimes it bends a pin and the fault shows up at functional test, an hour later, on a board that already has thirty components on it.
That is the case for the shroud. It is not a quality difference in the pin itself.
What it costs you
| Open pin header | Box header | |
|---|---|---|
| Footprint | Pins only, 2.54 mm grid | Adds about 1.3 mm of wall on each side |
| Board space for 2×10 | 25.4 × 5.08 mm | 25.4 × 7.7 mm |
| Mating protection | None | Wall plus keying slot |
| Price at 5,000 pcs | Baseline | Roughly 15 to 25% higher |
| Assembly | Visual alignment by hand | Drops in, one orientation |
| Typical use | Programming, jumpers, press-fit links | Ribbon cable, field service, anything unplugged |
The price gap is smaller than most people expect. On a 2×10 at 5,000 pcs it is usually a few cents per part. Compare that with one reworked board and the argument is over.
Where the open header is still the right call
Three cases come up often in quotes.
- Programming and test points. The header is used once at the factory. Nobody plugs into it again, so nothing needs guiding.
- Board stacking with a socket on the other side. The female header already has a body that guides the pins. A shroud on top of that adds height and cost for no gain.
- Height-limited enclosures. A box header adds 2 to 3 mm of wall height. On a low profile assembly that is the difference between closing the lid and not.
What we see on drawings
Most of the mistakes we correct at quotation stage are not about the header type. They are about the tail.
If the board is 1.6 mm and the tail is 3.0 mm, the solder fillet has enough to grab. On a 2.0 mm board with the same tail, the pin barely clears the pad and you get cold joints that pass visual inspection. On a 0.8 mm board it is worse. Tell us the board thickness when you send the drawing. Tail length comes off the same die, we just form it differently.
Second one: right angle parts. The bend is fixed at 90 degrees. If the drawing calls for 85 or 95 degrees, that is a new forming die, not an adjustment.
Questions we get
Can I use a box header where the drawing says pin header?
Only if there is room for the wall. The pin positions are the same, the footprint is not. Check the keep-out area around the connector before you substitute.
Does the shroud change the current rating?
No. Both are 3 A per pin with brass contacts. The limit comes from the pin and the plating, not the plastic around it.
Do you make both from the same position counts?
2×5 to 2×40 from existing molds. Anything outside that needs a new mold, about 15 days. Prototype quantities we can build from the standard mold and cut down.
If you are still deciding
Send the drawing or a photo of the board with a ruler next to the connector. We quote both versions with the footprint difference marked, and you can see the space cost before committing. Samples of either type ship in 2 working days.