Pin Header, Dual Row, Right Angle

YT-PH254-2R

2.54 mm, 2×2 to 2×40, 90 degree bend.

  • Pitch is 2.54 mm.
  • Made from 2×2 to 2×40 positions, dual row.
  • Mounting type: Right angle.
  • Rated 3 A per pin at 500 VAC.
  • Housing is PA6T, UL94V-0.
  • Minimum order 2,000 pcs; samples ship in 7 to 10 days.
  • Samples 7–10 days
  • Custom position counts
  • RoHS per shipment
  • Tube, tray or tape
Specification

YT-PH254-2R

ModelPitchRowsPositionsMountingContactInsulatorMOQ
YT-PH254-2R2.54 mmDual2×2 to 2×40Right angleBrass, gold platedPA6T, UL94V-02,000 pcs

Specification updated 19 November 2026. Dimensions in mm, ratings at 25 °C.

Rated current3 A per pin
Rated voltage500 VAC
PackagingTube
Pin length11.5 mm

Bent pins are the main cause of placement failures, so the forming die is serviced on a fixed schedule and pin straightness is checked in process.

If your board is thicker than 1.6 mm, tell us before we quote. The tail length may need to change.

When this part is not the right choice

Most quotation problems come from a part that fits the drawing but not the process. These are the cases where we would steer you elsewhere.

  • Shallow enclosures. The bend needs room behind the connector for the ribbon to fold. Below about 10 mm of clearance, use the straight version and route the cable along the board instead.
  • Cost-first wave-solder boards. PA6T costs more than PBT and the temperature margin buys nothing if the part never enters an oven above 200 °C.
  • Anything above the rated current. Ratings are per pin at 25 °C ambient. Bundle several loaded pins in a sealed enclosure and the derating is yours to calculate, not ours to guess.

On the assembly line

Bent pins are the usual failure point, so the forming die is serviced on a schedule and pin straightness is measured in process. Parts pack in tubes, standing on the housing rather than on the pins. Solder tails are sized for a 1.6 mm board by default. Tell us the board thickness at quotation and we form the tail to match; it comes off the same die.

Packing, MOQ and lead time

Minimum order is 2,000 pcs. Samples are free of charge and leave in 7 to 10 days. Production runs about 15 days after sample approval, which covers molding, plating and the inspection record that ships in the box. Position counts from 2×2 to 2×40 are standard. Outside that range we cut a new mold, about 15 days. Every shipment includes a RoHS declaration and the lot inspection record.

Questions buyers ask

Does the YT-PH254-2R support reflow soldering?

YT-PH254-2R uses a PA6T housing, which takes reflow at 260 °C for 10 seconds. It can go through a lead-free oven with the rest of the board.

What is the minimum order quantity for the YT-PH254-2R?

Minimum order is 2,000 pcs. Samples are free of charge and ship in 7 to 10 days; production runs about 15 days after sample approval.

Can the position count of the YT-PH254-2R be changed?

Yes. Standard tooling covers 2×2 to 2×40. A count outside that range needs a new mold, about 15 days, and there is no tooling charge for counts we already run.

Same family

Pin Headers models

Category page
ModelPitchRowsPositionsMountingContactInsulatorMOQ
YT-PH127-2 1.27 mm Dual 2×2 to 2×50 SMT Brass, gold plated PA6T, UL94V-0 2,000 pcs
YT-PH200-1 2.00 mm Single 1×2 to 1×40 Straight Brass, gold flash PA6T, UL94V-0 2,000 pcs
YT-PH254-2 2.54 mm Dual 2×2 to 2×40 Straight Brass, gold plated PA6T, UL94V-0 2,000 pcs
YT-PH254-1 2.54 mm Single 1×2 to 1×40 Straight Brass, gold plated PA6T, UL94V-0 2,000 pcs
Quotation

Send a drawing or a photo of the part.

WhatsApp is the fastest route. We answer during Beijing working hours (UTC+8), usually within a couple of hours. If you only have a sample, put a ruler next to it and take a photo.