IDC Box Header, Short Ejector Latch

YT-DC2S-254

2.54 mm, 6 to 50 positions, short latch for low enclosure lids.

  • Pitch is 2.54 mm.
  • Made from 6 to 50 positions, dual row.
  • Mounting type: Straight, short latch.
  • Rated 1 A per pin at 250 VAC.
  • Housing is PBT, UL94V-0.
  • Minimum order 2,000 pcs; samples ship in 7 to 10 days.
  • Samples 7–10 days
  • Custom position counts
  • RoHS per shipment
  • Tube, tray or tape
Specification

YT-DC2S-254

ModelPitchRowsPositionsMountingContactInsulatorMOQ
YT-DC2S-2542.54 mmDual6 to 50Straight, short latchBrass, gold platedPBT, UL94V-02,000 pcs

Specification updated 19 November 2026. Dimensions in mm, ratings at 25 °C.

Rated current1 A per pin
Rated voltage250 VAC
PackagingTube

The short latch clears a low enclosure lid. Retention is lower than the long latch, so this suits cables that are supported and not pulled.

People fit the short latch where the cable hangs, and the connector creeps out over a few hundred cycles. If the cable is not supported, use the long version.

When this part is not the right choice

Most quotation problems come from a part that fits the drawing but not the process. These are the cases where we would steer you elsewhere.

  • Boards that only see reflow. Through-hole parts add a selective solder or hand-solder step after the oven. If the assembly has no wave solder stage, an SMT version of the same footprint removes that step.
  • Reflow ovens. PBT softens near 200 °C. Boards that go through lead-free reflow need the PA6T version of the same footprint, which we also mold.
  • Connectors that are soldered and never touched again. The shroud adds 2 to 3 mm of height and a little cost, and buys nothing if nothing plugs into it.
  • Anything above the rated current. Ratings are per pin at 25 °C ambient. Bundle several loaded pins in a sealed enclosure and the derating is yours to calculate, not ours to guess.

On the assembly line

Parts pack in tubes, standing on the housing rather than on the pins, so the tails do not take the load in transit. Trays are available for short runs and odd position counts. Solder tails are sized for a 1.6 mm board by default. Tell us the board thickness at quotation and we form the tail to match; it comes off the same die.

Packing, MOQ and lead time

Minimum order is 2,000 pcs. Samples are free of charge and leave in 7 to 10 days. Production runs about 15 days after sample approval, which covers molding, plating and the inspection record that ships in the box. Position counts from 6 to 50 are standard. Outside that range we cut a new mold, about 15 days. Every shipment includes a RoHS declaration and the lot inspection record.

Questions buyers ask

Does the YT-DC2S-254 support reflow soldering?

YT-DC2S-254 is molded in PBT, which is a wave-solder part. PBT softens near 200 °C, so do not run it through a reflow oven. If the board is reflow-only, ask us for the same footprint in PA6T.

What is the minimum order quantity for the YT-DC2S-254?

Minimum order is 2,000 pcs. Samples are free of charge and ship in 7 to 10 days; production runs about 15 days after sample approval.

Can the position count of the YT-DC2S-254 be changed?

Yes. Standard tooling covers 6 to 50. A count outside that range needs a new mold, about 15 days, and there is no tooling charge for counts we already run.

Same family

Box Headers & IDC models

Category page
ModelPitchRowsPositionsMountingContactInsulatorMOQ
YT-BH254-2R 2.54 mm Dual 2×5 to 2×40 Right angle Brass, gold plated PA6T, UL94V-0 2,000 pcs
YT-BH254-2S 2.54 mm Dual 2×4 to 2×40 Straight Brass, gold plated PA6T, UL94V-0 2,000 pcs
YT-DC2-254 2.54 mm Dual 6 to 64 Straight Brass, gold flash PBT, UL94V-0 2,000 pcs
YT-DC3-127 1.27 mm Dual 6 to 68 Straight Brass, gold flash PA6T, UL94V-0 1,000 pcs
YT-DC2R-254 2.54 mm Dual 6 to 50 Right angle Brass, gold plated PBT, UL94V-0 2,000 pcs
Quotation

Send a drawing or a photo of the part.

WhatsApp is the fastest route. We answer during Beijing working hours (UTC+8), usually within a couple of hours. If you only have a sample, put a ruler next to it and take a photo.