IDC Box Header DC3, 1.27 mm

YT-DC3-127

1.27 mm DC3 footprint, 6 to 68 positions, for fine pitch ribbon.

  • Pitch is 1.27 mm.
  • Made from 6 to 68 positions, dual row.
  • Mounting type: Straight.
  • Rated 0.5 A per pin at 250 VAC.
  • Housing is PA6T, UL94V-0.
  • Minimum order 1,000 pcs; samples ship in 7 to 10 days.
  • Samples 7–10 days
  • Custom position counts
  • RoHS per shipment
  • Tube, tray or tape
Specification

YT-DC3-127

ModelPitchRowsPositionsMountingContactInsulatorMOQ
YT-DC3-1271.27 mmDual6 to 68StraightBrass, gold flashPA6T, UL94V-01,000 pcs

Specification updated 19 November 2026. Dimensions in mm, ratings at 25 °C.

Rated current0.5 A per pin
Rated voltage250 VAC
PackagingTube

Half the pitch of DC2, same footprint logic. Used where the board has no room for 2.54 mm spacing.

Pins are thinner, so the insertion force is lower and the contacts are easier to bend during handling. Keep the tube closed until the placement step.

When this part is not the right choice

Most quotation problems come from a part that fits the drawing but not the process. These are the cases where we would steer you elsewhere.

  • Boards that only see reflow. Through-hole parts add a selective solder or hand-solder step after the oven. If the assembly has no wave solder stage, an SMT version of the same footprint removes that step.
  • Cost-first wave-solder boards. PA6T costs more than PBT and the temperature margin buys nothing if the part never enters an oven above 200 °C.
  • Prototype boards built by hand. At 1.27 mm the pads are small enough that hand soldering produces more rework than the parts are worth.
  • Connectors that are soldered and never touched again. The shroud adds 2 to 3 mm of height and a little cost, and buys nothing if nothing plugs into it.

On the assembly line

Parts pack in tubes, standing on the housing rather than on the pins, so the tails do not take the load in transit. Trays are available for short runs and odd position counts. Solder tails are sized for a 1.6 mm board by default. Tell us the board thickness at quotation and we form the tail to match; it comes off the same die.

Packing, MOQ and lead time

Minimum order is 1,000 pcs. Samples are free of charge and leave in 7 to 10 days. Production runs about 15 days after sample approval, which covers molding, plating and the inspection record that ships in the box. Position counts from 6 to 68 are standard. Outside that range we cut a new mold, about 15 days. Every shipment includes a RoHS declaration and the lot inspection record.

Questions buyers ask

Does the YT-DC3-127 support reflow soldering?

YT-DC3-127 uses a PA6T housing, which takes reflow at 260 °C for 10 seconds. It can go through a lead-free oven with the rest of the board.

What is the minimum order quantity for the YT-DC3-127?

Minimum order is 1,000 pcs. Samples are free of charge and ship in 7 to 10 days; production runs about 15 days after sample approval.

Can the position count of the YT-DC3-127 be changed?

Yes. Standard tooling covers 6 to 68. A count outside that range needs a new mold, about 15 days, and there is no tooling charge for counts we already run.

Same family

Box Headers & IDC models

Category page
ModelPitchRowsPositionsMountingContactInsulatorMOQ
YT-BH254-2R 2.54 mm Dual 2×5 to 2×40 Right angle Brass, gold plated PA6T, UL94V-0 2,000 pcs
YT-BH254-2S 2.54 mm Dual 2×4 to 2×40 Straight Brass, gold plated PA6T, UL94V-0 2,000 pcs
YT-DC2-254 2.54 mm Dual 6 to 64 Straight Brass, gold flash PBT, UL94V-0 2,000 pcs
YT-DC2R-254 2.54 mm Dual 6 to 50 Right angle Brass, gold plated PBT, UL94V-0 2,000 pcs
YT-DC2S-254 2.54 mm Dual 6 to 50 Straight, short latch Brass, gold plated PBT, UL94V-0 2,000 pcs
Quotation

Send a drawing or a photo of the part.

WhatsApp is the fastest route. We answer during Beijing working hours (UTC+8), usually within a couple of hours. If you only have a sample, put a ruler next to it and take a photo.